IEEE 43-2013 PDF

IEEE Recommended Practice For Testing Insulation Resistance Of Electric Machinery Defines a recommended procedure for measuring insulation. The Institute of Electrical and Electronics Engineers (IEEE) standard for insulation resistance testing of motor and generator windings that was published in Content Description. Revision Standard – Active. The dc voltage tests procedures for the measurement of the insulation resistance and polarization index of.

Author: Fejinn Mazutaxe
Country: Swaziland
Language: English (Spanish)
Genre: Music
Published (Last): 24 December 2005
Pages: 205
PDF File Size: 1.18 Mb
ePub File Size: 10.7 Mb
ISBN: 842-7-63374-439-6
Downloads: 44616
Price: Free* [*Free Regsitration Required]
Uploader: Zolobei

After 1 minute with a random wound DUT, or minutes with a form wound DUT, this is typically the only current remaining unless the insulation is weak ieee dama There may be an increase in the surface leakage current on machines where a stress-control coating has been applied to the end-windings. Enter your personal account email address to request a password reset: This time interval is based on the R resistiveL inductiveC geometric capacitiveand absorptive characteristics of the circuit during charging time of the application of the voltage and discharging elapsed time since the removal of the voltage source and subsequent grounding of the winding under test.

The dc voltage tests procedures for the measurement of the ieee resistance and polarization index of insulated stator, and rotor windings and how to interpret the results are described in this recommended practice. IEEE is led by a diverse body of elected and appointed volunteer members. C, and taken at a specified time t from start of voltage application. Are you sure you want to empty the cart?

To find out if ieee leakage current is mainly a current or also contains the more damaging conductance current through the volume of the insulation to ground, one must do a step voltage test or ramp test to a test voltage one is comfortable with given the level of megohms measured.

Regardless of the cleanliness of the winding surface, if the winding temperature is at or below the dew point of the ambient air, a film of moisture may form on the insulation surface, which can lower insulation resistance or polarization index.

  DISTURBIOS HIDROELETROLITICOS PEDIATRIA PDF

The ifee component is due to the polarization of the impregnating materials because the organic molecules, such as epoxy, polyester, and asphalt, tend to change orientation in the presence of a direct electric field. Users will often go directly to a Hipot ieee The dc voltage tests procedures for the measurement of the insulation resistance and polarization index of insulated stator, and rotor windings and how to interpret the results are described in this recommended practice.

The IEEE Brand Identity Toolkit explains the basic usage rules for all corporate identity elements and how to utilize them to create a powerful and consistent communications pieces.

What’s new in the IEEE 43 insulation resistance testing standard? | EASA

Full Description Scope This document ieee a recommended procedure for measuring insulation resistance ieee armature and field windings in rotating machines rated W or greater.

Insulation Resistance IR is maybe the most common motor test. When IR is tracked over time, resistance values must be temperature compensated and the temperature must be above the dew point for comparisons of results to make sense.

Not Logged In Member?: For large machines with high capacitance, the inrush current can be high. It is recommended that subsequent ac high-potential testing not be conducted until the winding is fully discharged. The ground insulation certainly can be weak with conduction current flowing through ieeee insulation to ground, but this is often dwarfed by the surface currents.

This current is usually zero if the motor is new or undamaged. Safety considerations Insulation resistance testing involves the application iee high direct voltages to machine windings. Megohm measurements may be tracked over time to help determine when ieee motor or generator should be reconditioned.

The dc voltage tests procedures for the measurement ieee the insulation resistance and polarization index of insulated stator, and rotor windings and how to iere the results are described in this recommended practice. I G — Conductance current: The discharge current manifests itself in two components:. Register for a trial account. The surface ieed current may be significantly higher on large turbine generator rotors and dc machines, which have relatively exposed creepage surfaces. FORMAT Single User Subscription Site License Subscription BOOKS All Books PACKAGES All Packages EDITION to PUBLISHER.

  GOODNIGHT MISTER TOM MICHELLE MAGORIAN PDF

They were placed on your computer when you launched this website. See Annex A for the use of other values. All others, please contact us at info madcad. iieee

What’s new in the IEEE 43 insulation resistance testing standard?

These can only be obtained from the manufacturer of the motor. There are ieee temperature compensation formulas, and ieee one above may be the most conservative.

The IEEE Brand Identity Toolkit explains the basic usage rules for all eiee identity elements and how to utilize them to create a powerful and consistent communications pieces. Get a Quote Careers Exhibitions. I T — Total current: Copyright Compu-tecture, Inc. The strategic plan of IEEE is driven by an envisioned future that realizes the full potential of the role IEEE plays in advancing technology for humanity. Subscribe on standards — Read more. The governance structure includes boards for operational areas as well as bodies representing members in the 45 Societies and technical Iere and ten worldwide geographic regions.

Land Use 43-013 Development. Modern types of filmcoated wire, as well as epoxy-mica or polyester-mica insulated stator windings, may approach a constant value of insulation resistance in 4 min or less. The ground insulation certainly can be weak with conduction current flowing through the ieer to ground, but this is often dwarfed by the surface currents. No items in cart. Remember me for one month. For such insulation testers, the accuracy in the last digit s is not specified or is poor, iees for good reason.

There were no books found for the applied search filters.

The insulation resistance of a rotating machine winding is a function of the type and condition of the insulating materials used, as well idee their application technique.

Most insulation testers will do this automatically if the winding temperature is entered in the tester. Enter your account email address to request a password reset:

Back to top