KIMO MP 200 PDF

Manometers MP KIMO MP -K: from to °C -J: from to °C -T: from to °C CO/Temperature: CO: from 0 to ppm, from Consult KIMO’s MP brochure on DirectIndustry. Page: 1/4. This is the MP Thermo-Anemo-Manometer. It is an easy to use meter which can take complex measurements. The MP is designed to measure Air.

Author: Arashigore Arashiktilar
Country: Romania
Language: English (Spanish)
Genre: Medical
Published (Last): 20 January 2018
Pages: 61
PDF File Size: 6.6 Mb
ePub File Size: 12.99 Mb
ISBN: 701-8-56251-712-8
Downloads: 88254
Price: Free* [*Free Regsitration Required]
Uploader: Moogukasa

Probe Hold Alarms Params Veloci. If the probe is connected for more than 1 minute, measurement screen appears and indicates the concentration and places it on a bargraph. Click on OK to validate.

For measurement launching, click on OK with the access key. You can choose between a planned or a continuous dataset. In regards of Quality insurance norms, we recommend that the instruments are checked once a year.

Launch a planned dataset A planned dataset is composed of several locations. Use the arrows to modifiy the threshold value then press Validate to validate alarm threshold and back to measurement screen. With Pressure kiml, you can access to following sub-functions – Hold – see Air velocity – Config. Press 2x in order to select Min-Max function: For each location, the operator can enter a theorical value and a tolerance for the parameter to be controlled.

This datasets can’t be set using Datalogger Software. Preview of tables of points of datasets Dataset summary You can display tables of points of datasets performed on the device. Average – Rec Recording Veloci. It’s a community-based project which helps to repair anything.

  ARCHITECTURE AND TRANSGRESSION BERNARD TSCHUMI PDF

Kimo MP H MPH Thermo-Anemo-Manometer

This function can also be automatically performed by using the solenoid valve function. On enabled mode, the probe is connected, the measurement is carried out and the value is displayed. Configuration sub-function allows to: Enter dataset time and interval of time between 2 measurements by pm Period with access key.

Select Start for dataset launching. Create or launch a continuous dataset Select dataset A continuous dataset can be carried out using MP and is composed of several kiimo measuring oimo. Wire probes with Smart-plus system Wire probes with Smart-plus system are automatically recognized when connected to the instrument. The beep repetition frequency will increase accordong to the increase of detected gas concentration, and the display will blink at the same frequency.

Click on Mesure to display values table of selected dataset. The operator can choose an automatic kimk a manual dataset, with an instant value or an average. Air velocity with Pitot tube: The numbers of points is displayed. If the probe has been just connected, the screen indicates the remaining time of warm up then the measurement screen appears, indicates the concentration and places it on a bargraph. The ”Probe” menu only appears when probes or module are connected. From this screen you can: Select compensation It is possible to modify the value of the compensation in temperature.

Kimo MP200 Thermo-Anemo-Manometer

It is thus necessary to enter the real temperature of use to obtain more precise results. If Other is selected, you must enter a value. Press 1x in order to select HOLD function: Click on Esc to return to previous screen. When the solenoid valve is enabled, it runs every minute.

  CARAHUECA NICOLAS CASARIEGO PDF

Several actions are possible during the measurement: This sub-function allows to compensate for any long-term drifts of the sensing element by a manual adjustment of the zero. You can access this function selecting COmax with the access key CO max The CO is measured on an adjustable period, the maximum m measured in this period is called CO max.

From this screen, press Measure to back to measurement. Remove the front part at the back of the instrument. Alarm threshold corresponds to the right value on the bargraph. From this screen, you can: For others measurement modules, self-calibration is performed by disconnecting the two pressure inlets of the sensor, then by pressing ,p key.

Numbers of kio points and parameter for kjmo calculation is carried out, are displayed For adding a new measuring point to this calculation, press OK to confirm. If K factor is selected, you must enter value. If you click on average icon, max. To save your dataset click on Save with the access key. Go to Recording menu. On disabled mode, the probe is connected, the measurement is not carried out and the value is not displayed.

Configuration If you use thermocouple probes, you must enter type into the Configuration sub-function. To modify the period, press Period with the access key.

When the countdown is finished, the CO max is displayed.

Back to top